Other

- Plastic bar end plug pair for 22.2mm extensions

- Includes 61803 bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - These 61803 bearings are not interchangable with the 88/188 hub 61803 bearings

RockShox XLoc Parts

Alternator Flat Mount is an adjustable dropout system designed to offer flawless functionality with flat-mount brakes installed. The dropout plates move back and forth on the frame, controlled with a captive barrel nut and screw for a minimal appearance. - Compatible with frames designed for the Alternator Flat Mount standard - Accommodates a 12mm thru-axle - Allows the rear axle to be adjusted through a 15mm range - Note: This part number only includes a single Alternator Flat Mount plate - Hardware kits (sold separately) must always be paired with the style of dropout plates being installed on the frame

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 30mm - Outer Diameter: 42mm - Width: 7mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 24mm - Width: 5mm

- Mega Exo right hand threaded (RH) hollow carbon screws with a self-extracting cap - Designed to fit FSA MegaExo Cranks only - Includes bolt, self-extracting cap, and washers

The Race and Ergo Ultra pads allow riders to tune their setups for a snug fit. - New foam that resists being crushed for longer periods of time - Improved surface durability - Superior grip with a molded-in textured surface - Compatible with both the Ergo and Race armrest kits - Dimensions: Race (92.9mm x 887.5mm) or Ergo (108.4mm x 87.5mm) - Compatibility: Race / Ergo - Weight: 5mm: 21g / 10mm: 37g

Tellis Remote for i-Spec EV. - Tellis dropper post remote lever features light action with a forged alloy design - Fits 22.2mm diameter handlebars

Adapters to convert your flat mount fork to post mount calipers - FF-1 front 140mm rotor - FF-2 front 160mm rotor - FR-1 rear 140mm rotor - FR-2 rear 160mm rotor - Each includes two bolts

RockShox XLoc Parts

Have a current Bomber Z1 but missing that Coil Spring feel? Or, maybe you have a Bomber Z1 Coil already and want to customize its ride. Look no further. With this conversion kit, you can now convert your Bomber Z1 air fork easily to the Z1 Coil. Buy this upgrade kit and follow the install instructions (or have your bike shop swap it out for you) and you, too, will be riding the buttery-smooth Z1 Coil in no time. NOTE: To do the conversion, you will also need to purchase the Bomber Z1 Coil Conversion Spring

A five-piece IGUS bushing spacer kit for mounting rear shocks. - Compatible with x eyelet shocks using IGUS bushings mounted in the shock eyelet - Select the correct hardware kit for your mounting bolt diameter (e.g. 6mm, 8mm) and frame mount width (e.g. 22mm, 24mm)

- CHAINRING BOLT KIT 5X2 M8.5X7 / M8.5X5 STEEL BLACK, HIDDEN BOLT INCLUDING SPACER QTY 5

RockShox Volume Reducer Kits

- Lever Internals Gen 2 Guide RSC/Ultimate|Code RSC Qty 1

RockShox 35mm Seal Kit

Wolf Tooth ShiftMounts are adapter mounts that allow you to integrate SRAM and Shimano shifters with several different brakes from Shimano, SRAM, and more. Handlebar space is prime real estate and the ShiftMount seamlessly integrates brakes and shifters for a clean look. - Designed to work with rear (right side) brakes and shifters - Consult the brake and shifter manufacturers to understand which mounting interface you have on your brakes and shifters - For handlebar clamp ShiftMounts tighten clamp bolt to 1-2 Nm max torque - 6061-T6 aluminum - MM-ISII is for a SRAM MatchMaker shifter mounting to a Shimano I-SPEC II brake - MM-ISII is compatible with M9020, M9000, M8000, M7000, and M6000 brake levers - MM-ISII is compatible with, but not designed for SRAM AXS because the shift lever will be further towards the end of the bar, or closer to the rider's hand than is ideal for most riders

Replacement right and left Ergon logo bar plugs. Features the Ergon logo in a vibrant white color. You have the choice of a plug set of the barend and non-barend models - Right and Left soft plastic bar plugs. - Sold as a set only. - Fits most handlebars. - Can be trimmed to fit various handlebar thicknesses. - Plug set for GP and GS grips with barends - fits GP2, GP3, GP4, GP5, GS2 and GS3 models only - Plug set for GP1, GC1 and GS1 grips - fits GP1, GC1, and GS1 only

Replacement Barends for GP5 and GP5 BioKork Grips. - Note because of additional leverage of GP4 and GP5 bar ends, Ergon does not recommend using on carbon fiber handlebars - Glass fiber composite - For 2015 and newer grips

Cover kits for Magura brake levers.

Shiftmix adaptors allow a shifter to clamp directly to a Magura brake lever, expanding setup possibilities.

Magura Caliper Cover Ring Kit

These handy Problem Solvers Eccentric Bottom Bracket Shims allow you to fit your existing Eccentric Bottom Bracket into BB shells with inner diameters of 55mm or 57mm. - Anodized black - 6061 Aluminum

North Shore Billet Derailleur Hangers - All hangers are CNC machined from 6061 T6 Aluminum for strength and stiffness beyond OEM hangers - Protective anodized pewter finish - Hardware not included

North Shore Billet Derailleur Hangers - All hangers are CNC machined from 6061 T6 Aluminum for strength and stiffness beyond OEM hangers - Protective anodized pewter finish - Hardware not included

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss 3 Pawl Ring Nut

- Machined aluminum replacement derailleur hangers to fit a wide variety of frames - Please visit https://wheelsmfg.com/derailleur-hanger-tech-help for more updated info - Made in USA + Rocky Mountain Altitude Powerplay Alloy Carbon 2022; Blizzard Carb